Menu
YOUR ORDER
    Subtotal
    Shipping costs$10.50
    Total$10.50

    Pressurized Bottle DIY Beer Line Cleaning Kit – D System – 1.3 Gallon (5 Liter)

    Make it quick and easy to clean picnic pumps, direct draw boxes, and short-run beer systems using the 1.3 gallon (5 Liter) Pressurized Bottle DIY Beer Line Cleaning Kit. This bottle works with your D System direct draw beer dispenser.
    ... Read more
    # M5-801147
    $147.15Per unit
    In stock
    PA
    IL
    CA
    Description
    Specifications
    Replacement Parts
    Downloads
    Description
    Specifications
    Replacement Parts
    Downloads

    Make it quick and easy to clean picnic pumps, direct draw boxes, and short-run beer systems using the 1.3 gallon (5 Liter) Pressurized Bottle DIY Beer Line Cleaning Kit. This bottle works with most D System direct draw beer dispenser to force the appropriate cleaning solution through the lines and the tap, removing buildup.


    When you are ready to clean your system, simply untap the keg, fill this bottle with your choice of beer line cleaning solution, and tap the bottle. The bottle will pressurize and force the beer line cleaner through the lines when you open the tap, leaving your beer lines fresh and ready to use again. This bottle operates with a maximum pressure of 60 PSI and has an operating temperature of 36-68˚ F.


    FEATURES


    • 1.3 gallon (5 Liter) capacity
    • Maximum bottle pressure of 60 PSI
    • Fits most D System Keg Coupler
    • Makes it easy to clean direct draw systems
    • Includes bottle, cap, and dip tube


    Why You Should Clean Your Beer Lines: During use minerals, proteins, and carbohydrates build up in your dispenser lines. This affects the flavor and life of your beer, so keeping your direct draw beer system clean is of the utmost importance.


    CLEANING BOTTLE USE INSTRUCTIONS:

    Cleaning the lines is as simple as "tapping a keg."


    Setup:


    • Remove the cleaning bottle cap. Make sure the dip tube is attached to the bottle cap; if not, hold under hot water before applying to the cap to prevent the tube from splitting.
    • Mix warm (not hot) water and detergent per the manufacturer's instructions on the container.
    • Place bucket under beer faucet.


    Cleaning Beer Line:


    • Disconnect the coupler from the keg and connect it to the cleaning bottle.
    • Engage the keg coupler, and the bottle will pressurize, filling the line with a cleaning solution.


    Rinsing Beer Line:


    • Disconnect the keg coupler from the cleaning bottle.
    • Pull the pressure relief valve on the bottle to relieve bottle pressure.
    • Unscrew the bottle cap. Discard unused solution and thoroughly rinse the bottle.
    • Refill the bottle with cold fresh water.
    • Reconnect keg coupler to bottle.
    • Engage coupler. The bottle will pressurize, filling the beer line with rinse water.
    • Open the faucet to allow the cleaning solution and fresh water to flow out.
    • Allow the bottle to empty completely of rinse water.


    NOTE: If the dip tube is not attached to the bottle cap hold the tube under hot water for a moment or two before applying to the cap. Softing the tube will prevent splitting.

    FAQ/ Related Articles
    Do I need to clean the equipment and how often?
    Importance of Beer Line Cleaning
    Direct Draw Beer Line Cleaning
    Beer Line Cleaning and ROI
    What is "Beerstone"?
    How can I easily clean a party pump?
    WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. www.P65Warnings.ca.gov
    Fast delivery
    Fast delivery
    Same day shipping
    Secure shopping
    Secure shopping
    With SSL protection
    Support hours
    Support hours
    Mon-Fri, 8 a.m. - 4:30 p.m. on (866) 327-4159