I used chat a few weeks ago for help in building a modification to my kegerator. Through the help of micromatic, I built a parts list and recently ordered them. I received all my parts yesterday and started piecing everything together. Basically my goal was to purchase a larger CO2 tank(5#), cut a hole in my fridge wall, and run the co2 line through the fridge wall. I purchased hose(553R), washers(759), Tailpieces(526E), nuts(874), and a sleeve(CPC-100). When piecing everything together last night, I found a couple issues with what I was suggested to order. First, the nuts do NOT fit the connection on my regulator. The nut does fit onto the tap. The connection on my regulator is MUCH smaller. I
Announcement
Collapse
No announcement yet.
HELP with CO2 Connections
Collapse
X
-
The nut does fit on the coupler the way I read this. So your only issue is the output of the regulator? It needs to be a barbed fitting as pointed out. Hard to tell from the quality of the picture, but my guess would be after the shut off you would be able to unscrew the double male threaded fitting and replace it with a thread-to-barb connection. Or unscrew from the shut off down and replace with this;
Beer Gas Regulator ShutoffLast edited by djc; 02-20-2014, 10:19 AM.What I have: Haier two tap, 525 faucets, tower cooler, 10' lines
Comment
-
Thanks for the replies. The nut does fit fine on the tap, my concern with that was the seal. Will the tailpiece, washer, and nut I have be enough to create a 100% gas seal or is my tailpiece suppose to have some type of O-ring? And I think I'll order the part that DJC recommended. That should work fine.
Comment
-
I think I'll take that threaded coupling off past my shutoff and just look for a 5/16" barb that will screw on there. Then problem solved. Last problem would be where I hook the gas up to my tap and the sealing issues. O-Rings? Neoprene washer?
Comment
-
PointPleasantNJBeerguy,
I think it is a Great Northern Frosty Keg Kegerator Beer Dispenser Fridge.
bjlasota,
Honestly buy a new regulator and tank, best and simplest way to run gas. If can't get new regulator and tank, just cut stock line and feed through hole (I think this is what you wanted to do originally) and reconnect the coupler side connection and you might be good.
I also think you really don't need a new tank, new regulator might be a better upgrade, new regulator should fit the stock tank (which should last at least 3 1/2 kegs before refill), also you don't need new CO2 lines if you use stock regulator as long as the coupler side fits right and has a gas check and/or neoprene washer.
KB
Comment
-
It is a great northern. I wanted a new tank for a few reasons. I work in a different time zone than I live, so most places are closed by time I get home. Also, my old tank blew a seal on a Saturday night right after tapping a keg. There were no places open so my result was getting a party pump and drinking it in a day. So I wanted a backup tank. I'll get the little tank repaired and use it as a backup. I bought new CO2 line because the one that came with the kegerator was too short and since the new tank won't fit inside, I'll need to modify the line to take it outside.
I pulled my shut-off valve off from my regulator last night and am going to stop by lowes and see if they have any 5/16" barbs.
Comment
-
bjlasota,
Can you keep membership updated regarding switching out parts? I swear the Great Northern regulator is the same one Nostalgia uses, it seems that a MM barb doesn't fit perfectly on the Nostalgia regulator. I have a funny feeling the regulator is metric, if you take the barb to a DIY store, they probably can check size and confirm if SAE or Metric, thanks.
KB
BTW you probably could use a 3/8 bard if a 5/16 can't be found, a little tight but hot water should get 5/16 hose over barb.
Sorry had to correct size, sometimes I confuse beer and gas lines, if you got things working, no problem, just let membership what is happening and if thing do and don't work, thanks.Last edited by KillianBoy; 02-24-2014, 03:08 PM.
Comment
Comment