06-18-2008, 06:33 AM
|
|
Member
|
|
Join Date: Jun 2008
Posts: 7
|
|
All foam low flow
I am a newbie with a Danby. I bought it used from a guy who never even plugged it in. I have a pony of Bud Light new co2 bottle full. Set at 12 psi. The keg has been in the fridge 16 hrs and I still get only foam at a very slow pour rate. the pour starts with a burp of foam and with in 20-30 seconds it stops then starts again. The foam flows only slightly larger than pencil lead. It takes
1 + minutes to fill a 12 oz glass of foam. I checked all the connections/couplers all were tight.
The only problem I could find was the coupler lever handle was missing and had broken at the base where the handle screws onto the shaft but still locks in. I am sure I have missed some important facts so if you have questions fire away. Thanks in advance for any and all help.
Bigsmooth
|
06-18-2008, 11:23 AM
|
|
Junior Member
|
|
Join Date: Jun 2008
Posts: 3
|
|
Check the temp, if it is to warm you will get foam. If it is cold enough then replace the coupler. If you know someone who works at a bar or beer distributor you can get one for free. The keg might be bad too. You can take it back and get a new one for free, just tell them your problem.
Last edited by millermike; 06-18-2008 at 11:29 AM.
|
06-18-2008, 12:25 PM
|
|
Super Moderator
|
|
Join Date: Nov 2007
Location: St. Louis, MO
Posts: 794
|
|
did you turn on the co2 on/off valve? Not just turning the bottle on at screw handle, but the on/off valve just after the co2 regulator.
__________________
____________________________________________
Sometimes when I reflect back on all the beer I drink I feel ashamed.
Then I look into the glass and think about the workers in the brewery
and all of their hopes and dreams. If I didn't drink this beer, they might
be out of work and their dreams would be shattered. Then I say to myself,
"It is better that I drink this beer and let their dreams come true than
be selfish and worry about my liver."
____________________________________________
|
06-18-2008, 02:36 PM
|
|
Member
|
|
Join Date: Jun 2008
Posts: 7
|
|
Yes sir I turned on the main valve on the tank as well as the in line on the pressure gauges.
Quote:
Originally Posted by cubby_swans
did you turn on the co2 on/off valve? Not just turning the bottle on at screw handle, but the on/off valve just after the co2 regulator.
|
|
06-18-2008, 04:49 PM
|
|
Member
|
|
Join Date: Jun 2008
Posts: 16
|
|
Just a thought. When was the last time the lines were cleaned? I know you said it had never even been plugged in, but if you have 12# of CO2 on the keg and it takes you a long time to pour a glass, either your beer line is too long, or your lines are clogged. Give them a once over for cleanliness and let us know the length of your tubing from the coupler to the tower.
|
06-19-2008, 04:18 AM
|
|
Member
|
|
Join Date: Feb 2008
Location: SEMO
Posts: 35
|
|
Your retaining ring for the check ball in the coupler may me missing getting the ball stuck in the line, or the coupler's probe may not be fully penetrating the keg.
Can you see beer in the line?
|
06-19-2008, 07:32 AM
|
|
Super Moderator
|
|
Join Date: Feb 2006
Location: , , .
Posts: 555
|
|
timg is right. Take off the nut that connects the beer line to the coupler. Turn it uprside down. Is there a ball that falls out of there. There should be a ball and a retaining clip that hold it in there. If this configuration is incorrect then you would end up experiencing the symptoms you are seeing.
|
06-19-2008, 09:11 PM
|
|
Super Moderator
|
|
Join Date: Mar 2005
Posts: 1,643
|
|
Or, there could be a beer worm growing in there!
|
06-20-2008, 09:18 AM
|
|
Member
|
|
Join Date: Jun 2008
Posts: 7
|
|
Ok problem solved. Replaced co2 gauge cluster, d coupler and both lines. I must say MMMMMMMMMMMM cold Draft beer at home is a must. Thanks for all your help fellas. May all your beer be cold and your wifes quiet. 
|
| Thread Tools |
|
|
| Display Modes |
 Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 02:36 PM.
Note:
Micro Matic’s Draft Beer Discussion forum is a public service which allows our members to share their draft beer knowledge and for visitors to view their discussions.
While Micro Matic's Dispense Institute instructors and knowledgeable staff are often participates in the forum, Micro Matic does not attempt to verify information posted by members. The information which members post are personal views, and may not reflect the views of Micro Matic. Micro Matic takes no responsibility and assumes no liability for any information posted by members, or results that occur from the information.
Micro Matic reserves the right to monitor, remove or edit content at its discretion.
|
|
|
Toll Free Orders:
1 (866) 291-5756
