Beer Forum

Search Forum                       Advanced Search

  #1 (permalink)  
Old 12-27-2006, 08:39 AM
Edge20 Edge20 is offline
Junior Member
 
Join Date: Dec 2006
Posts: 2
Default Home Long Line System

At the expense of revealing I am clearly a novice at this...

I have read countless posts and literature on extended line systems at home and here is my situation: (any suggestions / help is greatly appreciated!)

I purchased a dual faucet tower, standard length beer lines, gas lines, CO2 regulator, tank, and coupler for a home conversion system. I want to convert a refrigerator that is 10-15 feet away (and through a wall) to the dispensing kegarator. If I run the lines without a commercial grade glycol system ($$$) and insulate them with foam, will it work?

If so, what do you suggest I buy as extensions, connections, etc to complete the project?

Will the system balance if I run the tubing up over a doorway (5 feet above the keg level) and back down?

Thanks!
Bob
Reply With Quote
  #2 (permalink)  
Old 12-27-2006, 11:42 AM
mctripj mctripj is offline
Senior Member
 
Join Date: Jun 2006
Location: Fairbanks,Alaska, USA.
Posts: 51
Send a message via AIM to mctripj Send a message via MSN to mctripj Send a message via Yahoo to mctripj
Default

hey bob, welcome to the forum!
if what i am imagining by your description is correct, then you would want to run your lines through a 3-4 inch pvc/abs pipe and have a blower on the cold end to keep cold air blowing through the pipe and your lines cold. of course you will have to use elbows to get it up over the doorway and back down. just make sure you have a strong enough blower unit so your cf/m is high enough to keep it all cold. insulating the pipe isnt a bad idea either.
__________________
-jomo
Reply With Quote
  #3 (permalink)  
Old 12-27-2006, 02:00 PM
ernestbud ernestbud is offline
Senior Member
 
Join Date: Oct 2006
Location: Tulsa. Oklahoma
Posts: 100
Default

air blown systems are only effective up to 25' remember for every 90 deg turn you have to add 5' and yes insulate the pipes
Reply With Quote
  #4 (permalink)  
Old 12-27-2006, 08:39 PM
Edge20 Edge20 is offline
Junior Member
 
Join Date: Dec 2006
Posts: 2
Default

After looking at the potential setup again, it appears that the lines will run 12-15 feet at level with the tower (from the fridge via insulated tubing), but will travel through a wall and will be enclosed in a temperature controlled but NOT "actively" refrigerated/cooled area of the basement.

Is it possible and/or worth a shot to do this in an effort to save some money and at the expense of a little foam waste?

If not, I need to rethink my plan. Any suggestions for this first timer who is (unfortunately) on a budget?

Bob
Reply With Quote
  #5 (permalink)  
Old 12-28-2006, 07:09 AM
ernestbud ernestbud is offline
Senior Member
 
Join Date: Oct 2006
Location: Tulsa. Oklahoma
Posts: 100
Default

as long as the entire run is enclosed in the pvc pipe and insulated you should have minimal problems. just make sure that the blower that you put on is big enough and that it gets sufficient air to the tower make sure that the refigerator is cold cold cold and do not let the beer temp exceed 40 deg. remember that the back of the faucet should be the coldest spot in the system
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 09:43 PM.

Note:
Micro Matic’s Draft Beer Discussion forum is a public service which allows our members to share their draft beer knowledge and for visitors to view their discussions. While Micro Matic's Dispense Institute instructors and knowledgeable staff are often participates in the forum, Micro Matic does not attempt to verify information posted by members. The information which members post are personal views, and may not reflect the views of Micro Matic. Micro Matic takes no responsibility and assumes no liability for any information posted by members, or results that occur from the information. Micro Matic reserves the right to monitor, remove or edit content at its discretion.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO 3.0.0 RC6 © 2006, Crawlability, Inc.