08-16-2006, 12:08 PM
|
|
Junior Member
|
|
Join Date: Aug 2006
Location: , , USA.
Posts: 5
|
|
kegerator conversion need help
i just got all my stuff for a frig kegerator and need help with ware to start and what not to do. anything will help!!!
beer is for everyone
|
08-16-2006, 07:47 PM
|
|
Super Moderator
|
|
Join Date: Mar 2005
Posts: 1,481
|
|
|
08-16-2006, 09:43 PM
|
|
Junior Member
|
|
Join Date: Aug 2006
Location: , , USA.
Posts: 5
|
|
thanks scott how much better is the permium to the standard kit? also which type of cleaning kit would u recomend for a limited use system?
beer is for everyone
|
08-16-2006, 09:48 PM
|
|
Junior Member
|
|
Join Date: Aug 2006
Location: , , USA.
Posts: 5
|
|
also what kind of temp gauge should I get
beer is for everyone
|
08-17-2006, 04:57 AM
|
|
Moderator
|
|
Join Date: Feb 2006
Location: , , USA.
Posts: 708
|
|
I have one of the pressurized cleaning bottles that couples just as the keg does. And don't assume that because your system is limited use it needs cleaned less. Once that beer enters the lines and faucet, the bacteria does the same thing it does in a system that is drawn every minute. The flavor of your beer depends on you maintaining the lines at least once a month (I do mine weekly).
For a temperature gauge I suggest a GOOD freezer/fridge thermometer to monitor the cabinet temperature. The Wal-Mart ones are not good ones IMHO.
http://forums.the-hole.net/
|
08-17-2006, 12:17 PM
|
|
Junior Member
|
|
Join Date: Aug 2006
Location: , , USA.
Posts: 5
|
|
thanks
beer is for everyone
|
08-17-2006, 04:39 PM
|
|
Super Moderator
|
|
Join Date: Mar 2005
Posts: 1,481
|
|
The premium kit has a drip tray that has a hole for the shank and a cleaning kit. The cleaning kit should suffice for your use. Direct draw systems at retail are cleaned every two weeks. If you allow the maintenance to slip, you will know by taste.
This thermometer will read the liquid temperature all the time. Mount it out of the way so it does not get beat up by the keg. Calibrate it prior to installing. Fill small bucket or pot with ice and then pour in water. Dump additional ice in to acquire a consistent ice bath. Place device in bath and if it does not read 32F, while holding dial, turn nut on back until pointer reads 32F.
Scott Zuhse, Instructor Micro Matic Dispense Institute |
08-26-2006, 03:06 AM
|
|
Junior Member
|
|
Join Date: Aug 2006
Location: , , USA.
Posts: 5
|
|
my beer is foamy why the temp is ok the pressure is like 8-10 what is wrong? it has to run for a while to get the foam out why what am i doing wrong ?
beer is for everyone
|
08-26-2006, 06:07 AM
|
|
Moderator
|
|
Join Date: Feb 2006
Location: , , USA.
Posts: 708
|
|
Google keg balancing. About halfway down this page there is info on setting your pressures. http://www.alabev.com/draught.htm
|
08-27-2006, 09:28 AM
|
|
Super Moderator
|
|
Join Date: Mar 2005
Posts: 1,481
|
|
|
| Thread Tools |
|
|
| Display Modes |
 Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 10:13 PM.
Note:
Micro Matic’s Draft Beer Discussion forum is a public service which allows our members to share their draft beer knowledge and for visitors to view their discussions.
While Micro Matic's Dispense Institute instructors and knowledgeable staff are often participates in the forum, Micro Matic does not attempt to verify information posted by members. The information which members post are personal views, and may not reflect the views of Micro Matic. Micro Matic takes no responsibility and assumes no liability for any information posted by members, or results that occur from the information.
Micro Matic reserves the right to monitor, remove or edit content at its discretion.
|
|
|
Toll Free Orders:
1 (866) 291-5756
