
- Home
- Activity Stream
Activity Stream
New Activity ()
-
Older Activity
-
Today, 01:49 PM
Usually, yes. On a rare occasion the keg is so over carbonated it will be excess CO2, but based on where you've been pressure wise, I think it is...
11 replies | 166 view(s)
-
Today, 12:14 PM
I don't have an icing problem or a defrost problem other than it decides to go into defrost mode at inopportune times and when it does that it takes...
378 replies | 59513 view(s)
-
Today, 08:22 AM
Yeah, I ordered a nut with the new tailpiece, but the new nut wasn't large enough to fit on the coupler. There are gaps in the line. Does that mean...
11 replies | 166 view(s)
-
Today, 07:03 AM
Over in the BA forum I had suggested a new nut to match the tail piece for just the reason you mention, I'm glad the old pair worked out. Before you...
11 replies | 166 view(s)
-
Yesterday, 10:31 PM
rwegman01,
Never assume something is NOT the problem, a properly working tower cooler will circulate air AND prevent 1st beer foam, if beer is...
11 replies | 166 view(s)
-
Yesterday, 07:51 PM
Hi KB,
You are right, the original line is 3/8 I just measured it. Still only 4feet long and completly kinked from its orginal packagaing. It only...
11 replies | 166 view(s)
-
Yesterday, 07:16 PM
rwegman01,
Check out my Newbie thread, you really need to take things slower and have patience.
I doubt the ID of original line is 1/2, if brand...
11 replies | 166 view(s)
-
Yesterday, 06:11 PM
Well I was able to change the beer line, and it was much easier than I expected. I used all the hardware from the original one. The original one was...
11 replies | 166 view(s)
-
Yesterday, 04:58 PM
Pappy (stang68),
Sorry to hear about health problems, I had foot problems, which led to leg then back problems, ain't easy getting old.
Some models...
378 replies | 59513 view(s)
-
Yesterday, 03:58 PM
KB, yes it's been a while and things have been going good with the kegerator, not so with me, the retina in my right eye has detached twice since...
378 replies | 59513 view(s)
-
Yesterday, 03:45 PM
frost@41,
OK, so your water was 36.7 degrees early Wednesday roughly 48 hours ago, then you hooked up the ETC and the water dropped to 45 degrees,...
378 replies | 59513 view(s)
-
Yesterday, 03:16 PM
KB,
Did the resistor, and it dropped me 3-5 degrees, like you said. When the ETC came, I installed it (Pismo10 method) and after 24 hrs, I...
378 replies | 59513 view(s)
-
Yesterday, 03:05 PM
Todd,
LOL, well I guess i'm going that route then, Smithwicks it is.
Frost
4 replies | 100 view(s)
-
Yesterday, 03:01 PM
Pappy (stang68),
Been a while, I been waiting on a Danby pro to show but most questions are answered in this thread.
OK, I assumed that your Danby...
378 replies | 59513 view(s)
-
Yesterday, 01:54 PM
It is excellent on draft. Just a couple of things to be aware of:
1) You will need a "U" style coupler such at this -
...
4 replies | 100 view(s)
-
Yesterday, 01:15 PM
Todd,
You are correct. I am excited to try out the different beers on draft. I noticed that you have listed Smithwicks, I love this beer in...
4 replies | 100 view(s)
-
Yesterday, 09:42 AM
Berkshire Brewing Company Steel Rail Extra Pale Ale = 2.4 from Gary Bogoff at BBC via email
109 replies | 50879 view(s)
-
05-16-2013, 04:59 PM
I've read post after post regarding hooking up an external controller and don't think I can do any of the cutting wires, etc. I have the following...
378 replies | 59513 view(s)
-
05-16-2013, 04:29 PM
djc and rwegman01,
Note that this model isn't like older Danbys, it has a normal thermostat. Basically it like any other home kegerator out there....
11 replies | 166 view(s)
-
05-16-2013, 02:33 PM
Frost, there are so many great craft brewers out there now, from very small to the "macro" craft breweries like New Belgium and Sierra Nevada, to the...
4 replies | 100 view(s)
-
05-16-2013, 09:46 AM
I should stop and let others chime in. Here you will get a lot of feedback from other Danby owners which will be more valuable than the help I can...
11 replies | 166 view(s)
-
05-16-2013, 09:06 AM
Ha thanks Doug! Your the one answering my question no matter where I go!
11 replies | 166 view(s)
-
05-16-2013, 08:58 AM
Welcome from the Beer Advocate site. To get to the connection at the top of the tower you should be able to pop the top off the tower and hopefully...
11 replies | 166 view(s)
-
05-16-2013, 08:14 AM
Bought a Danby kegerator last week, and had terrible foam problems after tapping a keg of Honkers Ale. Reading other threads I found out about...
11 replies | 166 view(s)
-
05-16-2013, 05:55 AM
definetly mis-spoke. I have had the kegerator for only about 4 months and have had the problem ever since, not matter what i was running obviously. ...
8 replies | 126 view(s)
-
05-16-2013, 05:32 AM
tmoney,
I myself stopped reading when I saw you basically solved your problem. djc's post brings up the topic of clarity, when you said "Current...
8 replies | 126 view(s)
-
05-16-2013, 05:26 AM
Up above you had said you were running 2 Lite's. With the great options out there and the great capacity of the TDD-3 it would be a crime against...
8 replies | 126 view(s)
-
05-16-2013, 04:14 AM
Djc, what is wrong with running 2 kegs of lite? haven't actually done this. One keg was actually shiner and other miller lite. Just curious.
8 replies | 126 view(s)
-
05-15-2013, 08:33 PM
I think the bigger issue is running two kegs of Lite at the same time.
8 replies | 126 view(s)
Note:
Micro Matic’s Draft Beer Discussion forum is a public service which allows our members to share their draft beer knowledge and for visitors to view their discussions.
While Micro Matic's Dispense Institute instructors and knowledgeable staff are often participates in the forum, Micro Matic does not attempt to verify information posted by members. The information which members post are personal views, and may not reflect the views of Micro Matic. Micro Matic takes no responsibility and assumes no liability for any information posted by members, or results that occur from the information.
Micro Matic reserves the right to monitor, remove or edit content at its discretion.
|